LiteSpeed Load Balancer

LiteSpeed Load Balancer (LSLB) is a high-performance, content-aware, session-aware HTTP application load balancer. It can forward requests based on request content as well as session stickiness preference. LiteSpeed Load Balancer can help scale your application beyond one server deployment, as well as improve the reliability of your service in case of hardware failures.
GLOBAL Semiconductor Alliance says it will increase awareness and visibility worldwide for its 3D integrated circuit initiative.

The GSA has retained semiconductor industry veteran, Herb Reiter to lead the 3D IC initiative. It has also formed relationships with IMEC, ITRI, SEMI, SEMATECH and Si2 to help direct and participate in this effort.
D you know Integrated Circuit . What we didn't realize then was that the integrated circuit would reduce the cost of electronic functions by a factor of a million to one, nothing had ever done that for anything before" - Jack Kilby


The Integrated Circuit

It seems that the integrated circuit was destined to be invented. Two separate inventors, unaware of each other's activities, invented almost identical integrated circuits or ICs at nearly the same time.Patents for the Integrated Circuit

digital clock / calendar / thermometer


Here is a finely made digital clock with calendar and thermometer.

It is based on Microchip PIC16F628 (or PIC16F84) microcontroller and DS18S20 or DS18B20 temperature sensor from Maxim-IC. The hardware is pretty easy because it contains only a PIC microcontroller, DS18S20/DS18B20 sensor, 4x7 segment LED display with common anode, four 2N3906 transistors and several resistors.

The project site can also be found and the project: a digital thermostat.



here we can see some pictures of the new project of our member forums [Kiza].

This is a POV clock-in, maybe even the best so far. The program for microcontroller is written in Bascom-AVR and has only 3000 lines of code.

"The list of parts: ATmega324P @ 20MHz, 64KB Ramtron FRAM, FM1608, 5 x TLC5916 shift registers, 40 x Cyan PLCC-4 Ledić, A1101 Hall IC, TSOP6238 IR receiver and MIC5209-5.0 LDO V-Reg.
This is how to actually only the head of thermal printer and the printer does not complete. Management of the whole printer would be much easier, just send a couple of AT commands and it starts to print the desired information. In this case, the author had to make a "font" in the firmware, to control two servo motors and warming elements on the print head.

Microcontroller that is used with the Atmel AVR Arduino bootloader-om. Warming elements are controlled with a ULN2801A Darlington transistors that are again controlled by SN74164 shift register to preserve a lot of IO pins. See the video printer in action.

TURN SIGNAL SWITCHER



This is quite simple but may at first be confusing for MGA owners and mechanics. Notice the picture of the back end of the vacuum regulated turn signal switch for the MGA (and some other cars of the era). The terminal designations molded into the housing are "F", "L", and "R".

For the MGA 1500 the "F" can mean Flasher. For the MGA 1600 the "F" can mean Fuse. This is the power input terminal for the switch. The "L" and "R" terminals would seem to be labeled for Left and Right turn signals, but for the MGA this is backward, where "L" is connected to operate the Right turn signal and "R" is connected to operate the Left turn signal.

This seemingly odd terminal labeling likely originated with an earlier application where the manual input knob, shaped like a single wing, was installed with the wing oriented upward from the shaft. Then when you push it toward the left the shaft would rotate anti-clockwise, and toward the right would rotate clockwise. That is the direction of rotation required for these terminal designations to make sense.

As this switch is installed in the MGA, the wing on the knob hangs downward. Pushing it to the left makes the shaft rotate clockwise, and to the right rotates anti-clockwise. This means you have to hook up the Left turn signal wire to the "R" terminal, and the Right turn signal wire to the "L" terminal. If your MGA turn signals seem to work backward, this is likely the problem and the fix. When in doubt, use a test light or ohm meter to check continuity for the switch terminals when you operate the input knob. Also pay attention to the color coding on the wires.

Recent Post

eXTReMe Tracker
oes elektro diagram honda modif house luxury autocar zonadownload gossip celeb modif car